How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
Are you interested in info on How to Install a Bathtub Yourself?
Installing a bathtub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is conveniently obtainable, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub as well as set in the new one. See to it you have actually certified yourself for the job and also fit attempting it. Rather than working with a service provider to take control of a halfway-completed project, it is better to consider employing one before you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will certainly assist you set up a brand-new bath tub in your shower room if you have already acquired a brand-new bathtub as well as don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as additionally inspect the overflow outlet and the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub should wait till the bath tub has been used at least when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the faucet and the sink. Secure the faucet in position with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be linked to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath and the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is a good idea to fit the tiles using waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that editorial on A Step-by-Step Guide to Installing a Bathtub through a friend on our other domain. Sharing is caring. You won't know, you could be helping someone out. Thank you so much for going through it.
Click Here To Read More
Report this page